Recent Content by slow67

  1. slow67
    Post

    Spool and manual steering on a street car?

    I daily drive a spool (with power steering), and it is no issue (unless in a tight parking lot as stated before). I even parallel parked it over...
    Post by: slow67, Jul 16, 2013 in forum: Non-Turbo Tech questions
  2. slow67
    Post

    GRENADE teardown/autopsy. This should be fun!

    Sorry I misspoke, it shook the rings from a flexing cylinder.
    Post by: slow67, Aug 29, 2012 in forum: LS1, LS2, LS6, LT1, SBC Turbo and other GM Specfic Turbo Tech
  3. slow67
    Post

    Some info on gt45 y2004k china turbo.(new pics)

    Haha oops, read it too fast. Yes, he is on a single
    Post by: slow67, Aug 29, 2012 in forum: DIY and Junkyard Turbo Tech
  4. slow67
    Post

    Some info on gt45 y2004k china turbo.(new pics)

    denmah has tried it on an LSx 4.8L and 5.3L.
    Post by: slow67, Aug 29, 2012 in forum: DIY and Junkyard Turbo Tech
  5. slow67
    Post

    GRENADE teardown/autopsy. This should be fun!

    The only 2 ways I've heard of rings killing a motor is: 1. Too tight of a gap (obvoiusly) 2. According to some users on the bullet, you can rattle...
    Post by: slow67, Aug 28, 2012 in forum: LS1, LS2, LS6, LT1, SBC Turbo and other GM Specfic Turbo Tech
  6. slow67
    Post

    Took the pit bike out. Have a laugh at my expence.....

    Small bikes are definitely harder to ride.
    Post by: slow67, Aug 21, 2012 in forum: Videos Forum
  7. slow67
    Post

    Home Brew Tire Doping

    Here is someone capitalizing on their homebrew stuff: - link removed by staff, was giving virus warning -
    Post by: slow67, Aug 15, 2012 in forum: Non-Turbo Tech questions
  8. slow67
    Post

    blowing thru convertor or first gear band?

    If you have no low band, you have no reverse either.
    Post by: slow67, Aug 14, 2012 in forum: Non-Turbo Tech questions
  9. slow67
    Post

    Overdrive units..?

    Some OD trannies can be setup for full manual. Also US Shift makes controllers for under $600.
    Post by: slow67, Aug 13, 2012 in forum: Non-Turbo Tech questions
  10. slow67
    Post

    Overdrive units..?

    Jakes Performance builds a killer 4L80E transmission (and he can put an aftermarket reid bell on them). Also he has a couple of different in house...
    Post by: slow67, Aug 10, 2012 in forum: Non-Turbo Tech questions
  11. slow67
    Post

    Overdrive units..?

    4L80E. Plenty of them behind fords. IMO, overdrive is only half of the equation. Lockup is the other half. In my car 70 mph is (26" tall tires and...
    Post by: slow67, Aug 9, 2012 in forum: Non-Turbo Tech questions
  12. slow67
    Post

    Hi Flow Rate MAFs

    Depends on what GM PCM is used. Gen IV PCMs speed density is a pain in the arse, and Gen III PCMs you have too low of a limit without scaling the...
    Post by: slow67, Aug 6, 2012 in forum: LS1, LS2, LS6, LT1, SBC Turbo and other GM Specfic Turbo Tech
  13. slow67
    Post

    Welding on turbine hsg..

    I've been told the nickel won't hold up to turbo exhaust heat. Lots of people just regular mild steel or stainless rods when welding LSx...
    Post by: slow67, Aug 1, 2012 in forum: DIY and Junkyard Turbo Tech
  14. slow67
    Post

    Mark Whalberg getting flack over 9-11 comment.

    http://en.wikipedia.org/wiki/List_of_aircraft_hijackings It seems after 9/11 there is higher percentage of highjacked planes retaken by the cabin.
    Post by: slow67, Jul 26, 2012 in forum: General Discussion Forum For Non-Auto Topics
  15. slow67
    Post

    Three or six bolt torque converter flange?

    I'm pretty sure is nice and thick.
    Post by: slow67, Jul 25, 2012 in forum: Non-Turbo Tech questions
Loading...